Linuxant Linux drivers for Conexant chipsets - HSF driver installation      
company drivers
General
ALSA (audio) driver
ALSA (ppch) driver
HSF (softmodem) driver
DGC (modem) driver
HCF (modem) driver
RIPTIDE (audio) driver

HSF driver installation

Please see the README file for general information.

BEFORE INSTALLING

Remove any old HSF modem drivers, either manually or by running "rpm -e hsfmodem" or "make uninstall" if using the RPM or tar versions of this package respectively.

Note: if you had an older version of this package, it might have been installed under the previous "hsflinmodem" name. In that case, run "rpm -e hsflinmodem" (or "make uninstall" in the *old* package tree).

INSTALLATION INSTRUCTIONS

If your Linux distribution supports the RPM Package Manager, it is easiest to install the binary RPM package with METHOD A. If your system is based on Debian (DPKG), METHOD B is for you. METHOD C is for distributions without RPM or DPKG support, or those who prefer not to use packages.

If you obtained the driver as a ".zip" file, extract it first with "unzip <filename>.zip".

METHOD A: BINARY RPM PACKAGE (*.{arch}.rpm)

If you have obtained the driver package in RPM format:

1. install the rpm with "rpm -i hsfmodem-{version}.{arch}.rpm"

2. if necessary, run "hsfconfig" to complete the installation, enter license information, or to change your modem's configuration.

If you need to rebuild the generic RPM from source, you can get the TAR package and run: "rpmbuild -tb hsfmodem-{version}.tar.gz" (if rpmbuild is not found, you might have to install the rpm-build package or if you have an older RPM version, try "rpm --rebuild ..."). If you want a pre-compiled package for the currently running kernel, you can try "make rpmprecomp" in the top directory.

METHOD B: DEBIAN PACKAGE (*.deb)

If you have obtained the driver package in DEBIAN format:

1. install the package with "dpkg -i hsfmodem_{version}_{arch}.deb", if apt-get or some other tool hasn't already done it for you.

2. if necessary, run "hsfconfig" to complete the installation, enter license information, or to change your modem's configuration.

If you need to rebuild the Debian generic package from source, you can get the TAR package, and from the top directory run: "make debdist". A pre-compiled DEB package for the currently running kernel can be built using "make debprecomp" instead.

METHOD C: TAR PACKAGE (*.tar.gz)

If you have obtained the driver package in tar format:

1. extract the package with "tar -xzf hsfmodem-{version}.tar.gz"

2. change to the package directory with "cd hsfmodem-{version}"

3. run "make install" from the top of the package directory.

4. run "hsfconfig" to complete the installation and configure your modem.

Do not delete or move the source tree from your system after these steps, it will be required to uninstall and patch the driver.

(Alternatively to this whole procedure you may generate RPMS from the tar package using rpmbuild -ta hsfmodem-{version}.tar.gz")

AFTER INSTALLATION

If an error occurred during installation, please see the sections 'BUGS' and 'REPORTING PROBLEMS' below.

Once the modem is installed and configured, you may access it as /dev/ttySHSF0. Additionally, you can use it via the symbolic link /dev/modem (equivalent to ttySHSF0). If you have more than one HSF modem, the second will be available as /dev/ttySHSF1, the third as /dev/ttySHSF2 and so forth.

Please review the permissions on the device nodes with "ls -l" to ensure that they are adequate for your system.

The "hsfconfig" command can be used to change certain modem configuration options or recompile (generic packages only) the kernel modules after installation. Run "hsfconfig --help" for usage information.

LICENSE KEYS / REGISTRATION

To enable your modem's full functionality (high-speed 56k data and FAX), a license registration key must be obtained from Linuxant and entered with "hsfconfig --license".

Without a proper license key, the modem can only operate in FREE mode, limited to a maximum speed of 14.4Kbps (V.32bis) and the FAX functionality will not be available.

CHANGING REGIONAL SETTINGS

With "hsfconfig --region" you may select another region (country) supported by the modem.

MANUALLY UNLOADING THE DRIVERS

The modem drivers can be manually unloaded using the "hsfstop" command.

USING ALTERNATIVE VENDOR AND DEVICE IDS

If your modem uses a chipset supported by the drivers but isn't recognized by the driver, please contact modem.support@linuxant.com.

DOCUMENTATION

See the included document 100498D_RM_HxF_Released.pdf (viewable with Adobe Acrobat reader or other PDF readers).

REMOVING THE DRIVER

If for any reason you wish to un-install the HSF drivers from your system, simply run the "hsfconfig --uninstall" command in a root shell.

MORE INFORMATION AND HELP

If you require license keys, assistance or need more information, go to: http://www.linuxant.com/drivers

Conexant Systems neither distributes nor maintains this package. PLEASE DO NOT CONTACT CONEXANT REGARDING THIS SOFTWARE!!!

BUGS

A list of currently known problems is included in the file "BUGS".

BAD CONNECTIONS

If you experience sudden disconnects or bad connections, please check the last call status information, which can be obtained with the AT#UG command or "cat /proc/driver/hsf/0/lastcallstatus". Alternatively the driver can be configured to automatically log this data upon carrier loss by adding the "loglastcallstatus=1" parameter to the "options hsfserial" line in /etc/modules.conf or /etc/modprobe.conf.

REPORTING PROBLEMS

Additional problem reports or patches may be sent to: modem.support@linuxant.com

Enclosing the output of "hsfconfig --dumpdiag" and the last call status information if pertinent (see above) in your report can greatly facilitate problem resolution.

 

Copyright © 2003-2008 Linuxant inc. All rights reserved.
Linuxant™ and DriverLoader™ are trademarks of Linuxant inc.
Linux is a trademark of Linus Torvalds in the US and some other countries.
Conexant™ and some product names are trademarks of Conexant Systems Inc.
Other trademarks belong to their respective owners.