[hsflinux] Disconnect immediately after CONNECT
ian silvester
yan at b13.net
Mon Oct 27 18:27:38 EST 2003
Hi all,
I have just upgraded to the full HSF modem driver, in a failed attempt to fix a connection problem I was having.
My problem is this. The modules all load up just fine, KPPP sees and can query the modem, when I dial I can hear the modem tones and arbitration occurring between the modems. The log window gets as far as displaying CONNECT 57600, then immediately the status bar of the log window displays 'Starting kpppd..' and a redial is attempted. This loop goes on ad infinitum until I hit 'Cancel'. I upgraded to the full driver on the basis that the remote modem was refusing to talk down to 14.4K, but the upgrade has not changed the symptoms, including the various log contents. I have a Fujitsu-Siemens C1020 (VIA chipset), running Debian Woody with a 2.4.20 kernel and ACPI 20021212 (my hardware has no APIC, by the way).
I've been through the FAQ and mailing list archive to no avail. There are obviously a few error outputs in the logs I've supplied (below), but they don't seem to add up to me, can you shed any light?
Regards,
Dr. Ian Silvester
/proc/driver/hsf/0/lastcallstatus:
<#UG VERSION=3>
<DRIVER VERSION=hsfmodem-6.03.00lnxt03091800full>
<CALL SETUP RESULT=Detected No Recognizable Tone>
<MULTIMEDIA MODE=Data Only>
<DTE-DCE MODE=Async data>
<V.8 CM="">
<V.8 JM="">
<RX SIG PWR DB=0, TX SIG PWR DB=0, S/N RATIO DB=0>
<RTD=0>
<TX MOD=V.17, TX SYMBOL RATE=0, TX CARRIER FREQ=0>
<RX MOD=V.17, RX SYMBOL RATE=0, RX CARRIER FREQ=0>
<TX FIRST RATE=0, RX FIRST RATE=0>
<CARRIER LOSS=0, RATE RENEG=0>
<RETRAINS REQ=0, RETRAINS DET=0>
<TX FINAL RATE=0, RX FINAL RATE=0>
<PROTOCOL=None>
<EC FRAME SIZE=0>
<EC LINK TIMEOUTS=0>
<EC LINK NAKS=0>
<COMPRESSION=None>
<COMPRESSION DICTIONARY SIZE=0>
<TX FLOW CONTROL=0>
<RX FLOW CONTROL=0>
<TX CHARS SENT FROM DTE=7>
<RX CHARS SENT TO DTE=2A>
<TX CHARS LOST=0>
<RX CHARS LOST=0>
<TX FRAME COUNT=0>
<RX FRAME COUNT=0>
<TX FRAME ERROR COUNT=0>
<RX FRAME ERROR COUNT=0>
<TERMINATION CAUSE=Key abort>
<CALL WAITING EVENT COUNT=0>
<LSD Vdd=0, Power Bits=0>
<V8BIS DSP VER=0>
<RATE RENEG REQ=0, RATE RENEG DET=0>
<RBS=0, AltRBS=0>
<DIG PAD DET=0, DIG LOSS EST=0, IMD RATIO=0, SPEED DROP=0>
<HS CNT=0, Det1=0, Res1=0, LAPM=0>
<EQM=0, TRAINING EQM=0>
<HandShake Time=0.0>
<DIB ERROR COUNTERS=0, 0, 0, 0, 0, 0, 0, 0>
/proc/driver/hsf/0/hwinst:
0-PCI-1106:3068-10cf:118e
/proc/driver/hsf/0/hwprofile:
hsfmc97via
/proc/driver/hsf/0/hwrevision:
CXT29
lsmod:
Module Size Used by Not tainted
ppp_generic 16716 0 (autoclean)
slhc 4352 0 (autoclean) [ppp_generic]
hsfmc97via 33192 0
hsfserial 27904 0 [hsfmc97via]
hsfengine 1007488 0 [hsfserial]
hsfosspec 39520 2 [hsfmc97via hsfserial hsfengine]
hsfsoar 47944 0 [hsfmc97via]
snd-pcm-oss 35200 0 (autoclean)
snd-mixer-oss 8864 0 (autoclean) [snd-pcm-oss]
snd-via8233 4768 0
snd-pcm 46368 0 [snd-pcm-oss snd-via8233]
snd-timer 9984 0 [snd-pcm]
snd-ac97-codec 22176 0 [snd-via8233]
snd 24008 0 [snd-pcm-oss snd-mixer-oss snd-via8233 snd-pcm snd-timer snd-ac97-codec]
soundcore 3268 3 [snd]
usb-uhci 21220 0 (unused)
usbcore 54624 1 [usb-uhci]
/var/log/messages (snippet):
Oct 28 11:38:31 yanbook kernel: ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
Oct 28 11:56:58 yanbook kernel: ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
Oct 28 12:01:16 yanbook kernel: ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
Oct 28 12:04:16 yanbook kernel: 0000158.612: DevMgr_StartCallingTone - Fax element doesn't exist<6>CSLIP: code copyright 1989 Regents of the University of California
Oct 28 12:04:16 yanbook kernel: PPP generic driver version 2.4.2
Oct 28 12:16:23 yanbook kernel: 0000189.462: DevMgr_StartCallingTone - Fax element doesn't exist0000220.232: DevMgr_StartCallingTone - Fax element doesn't exist0000596.402: DevMgr_StartCallingTone - Fax element doesn't exist0000651.872: DevMgr_StartCallingTone - Fax element doesn't exist0000814.992: DevMgr_StartCallingTone - Fax element doesn't exist<6>eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
/var/log/syslog (snippet):
Oct 28 12:15:38 yanbook modprobe: modprobe: Can't locate module ppp0
Oct 28 12:15:38 yanbook modprobe: modprobe: Can't locate module ppp0
Oct 28 12:15:38 yanbook pppd[1609]: The remote system is required to authenticate itself
Oct 28 12:15:38 yanbook pppd[1609]: but I couldn't find any suitable secret (password) for it to use to do so.
Oct 28 12:15:38 yanbook pppd[1609]: (None of the available passwords would let it use an IP address.)
dmesg:
Linux version 2.4.20 (root at yanbook) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Thu Oct 16 19:12:51 EST 2003
<snip>
BIOS-e820: 0000000016ff0000 - 0000000016ffffc0 (ACPI data)
BIOS-e820: 0000000016ffffc0 - 0000000017000000 (ACPI NVS)
<snip>
ACPI: have wakeup address 0xc0001000
<snip>
ACPI: RSDP (v000 OID_00 ) @ 0x000e5010
ACPI: RSDT (v001 INSYDE RSDT_000 00000.00001) @ 0x16fffbc0
ACPI: FADT (v001 INSYDE FACP_000 00000.00256) @ 0x16fffac0
ACPI: BOOT (v001 INSYDE SYS_BOOT 00000.00256) @ 0x16fffb50
ACPI: DBGP (v001 INSYDE DBGP_000 00000.00256) @ 0x16fffb80
ACPI: DSDT (v001 FUJITS EF4 00000.01049) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: auto BOOT_IMAGE=Linux ro root=302 resume=/dev/hda1
No local APIC present or hardware disabled
<snip>
ACPI: Subsystem revision 20021212
PCI: PCI BIOS revision 2.10 entry at 0xe8964, last bus=1
PCI: Using configuration type 1
ACPI-0263: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI-0263: *** Info: GPE Block1 defined as GPE16 to GPE31
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 1)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 9 14 15, enabled at IRQ 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 *9 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 *10 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 *10 14 15)
<snip>
ACPI: Processor [CPU0] (supports C1 C2, 16 throttling states)
<snip>
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
<snip>
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
acpiphp_glue: checking PCI-hotplug capable bridges under [PCI0]
acpiphp_glue: can't get bus number, assuming 0
acpiphp_glue: Total 0slots
<snip>
PCI: Setting latency timer of device 00:11.6 to 64
ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
PCI: Setting latency timer of device 00:11.6 to 64
ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
PCI: Setting latency timer of device 00:11.6 to 64
ttySHSF0 at I/O 0xe300 (irq = 10) is a Conexant HSF softmodem
0000158.612: DevMgr_StartCallingTone - Fax element doesn't exist<6>CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
0000189.462: DevMgr_StartCallingTone - Fax element doesn't exist0000220.232: DevMgr_StartCallingTone - Fax element doesn't exist0000596.402: DevMgr_StartCallingTone - Fax element doesn't exist0000651.872: DevMgr_StartCallingTone - Fax element doesn't exist0000814.992: DevMgr_StartCallingTone - Fax element doesn't exist<6>eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
lspci:
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 3148
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:0a.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:0b.0 Network controller: AIRONET Wireless Communications: Unknown device a504
00:0c.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8026
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 23)
00:11.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 23)
00:11.4 USB Controller: VIA Technologies, Inc. UHCI USB (rev 23)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio Controller (rev 30)
00:11.6 Communication controller: VIA Technologies, Inc. AC97 Modem Controller (rev 70)
01:00.0 VGA compatible controller: S3 Inc.: Unknown device 8d04
More information about the hsflinux
mailing list